Static Pressure Calculator
Enter your supply and return static readings to measure total external static pressure. Enter the manufacturer-rated maximum external static pressure and the calculator compares your measured value against it.
- Signed supply and return readings
- Manufacturer-rated limit comparison
- Follows the manufacturer's test procedure
Static pressure (TESP)
Enter supply and return static readings to measure total external static pressure. Both readings are required before a TESP result is shown.
- Enter each reading with its sign: the supply side reads positive, the return side reads negative.
- Example: +0.30 supply and -0.20 return gives TESP = 0.50 in. w.c. (TESP = supply pressure minus return pressure).
- A negative TESP result means the signs, hose connections, or test locations need checking.
- Test locations, probe placement, and whether filters, coils, and other components are included in the reading must follow the equipment manufacturer's procedure. Readings taken at different locations, or with different components included, are not comparable.
- TESP alone does not establish airflow. Compare TESP with the manufacturer's blower performance tables for the measured value.
- The manufacturer-rated maximum external static pressure is specific to each unit. Do not substitute a typical or assumed value for the rating of the equipment being tested.
How to take the readings
- Clean filter in place, all registers and grilles open, blower on the speed it runs in normal operation.
- Drill a test port in the supply plenum downstream of the coil, and one in the return plenum upstream of the blower.
- Static pressure tip facing into the airflow, tubing to the manometer — supply to the positive port, return to the negative port.
- Let it stabilize, then record both. Supply reads positive; return reads negative.
- Seal the test ports when you're finished.
TESP = supply pressure minus return pressure. With signed readings, +0.30 supply and -0.20 return totals 0.50 in. w.c. A dual-port manometer totals it for you; enter each reading with its sign, exactly as your instrument displays it.
What the number means
The maximum external static pressure is specific to each unit. Some are rated at 0.30 in. w.c., others as high as 0.80 or beyond, so there is no universal pass/fail number. The calculator shows your measured TESP without a verdict until you enter the manufacturer-rated maximum external static pressure from the nameplate or specification sheet. The blower performance table then tells you what airflow that static actually buys you.
Test locations, probe placement, and whether filters, coils, and other components are included in the reading must follow the equipment manufacturer's procedure. Readings taken at different locations, or with different components included, are not comparable, and TESP alone does not establish airflow.
If TESP is above the manufacturer's rating
The reading alone does not establish a specific fault. First verify the test locations, that the manometer is zeroed, and that the system was operating under the conditions the manufacturer's procedure specifies, then compare with the manufacturer's blower data. Once verified, common contributors to a high reading include:
- Filter — loaded, wrong size, or too restrictive a media for the system.
- Indoor coil — dirty, or fins flattened and blocked.
- Registers and grilles — closed, blocked by furniture, or undersized.
- Ductwork — undersized, kinked or crushed flex, long uninsulated runs.
- Return — too few return grilles.
If the measured TESP is low
A low reading is not automatically a pass. Verify the test locations, the manometer zero, and the blower operating conditions against the manufacturer's procedure before drawing any conclusion. If the reading verifies, compare it with the manufacturer's blower performance data, since a much lower measured static than the rating is consistent with operating at higher airflow than the rating assumes, and that is worth checking against the equipment's specified temperature rise.
This is one tool. The app is the whole job.
AI diagnostics, manufacturer error-code decoding, manuals and wiring diagrams, plus the full field toolkit — built for HVAC and refrigeration pros.
Free for 7 days — cancel before your trial ends and you won't be charged. After the trial you're billed $29 per month plus applicable tax, added at checkout; canceling later stops future billing without refunding the period already underway.
More free tools
Refrigerant PT Chart
Saturation pressure and temperature, both directions, for R-410A, R-32, R-454B, R-22, R-134a and more.
OpenDuct Sizing Calculator
Size round or rectangular duct from airflow and friction rate, with a velocity check built in.
OpenHeat Pump Balance Point
Find the outdoor temperature where heat pump capacity meets the home's heat loss, and the aux heat gap.
Open